\n
When using the Port Cutting Guide, ensure that the cutting bolts are located below the number 1 on the front of the Guide. The locking bolts go below the number 4 on the back of the Port Cutting Guide. <\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n
[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig6-positioning-cmt-port-cutting-guide.webp” alt=”figure 9 7 channel cmt port cutting guide with plugs” title_text=”Figure 9 – 7-Channel CMT Port Cutting Guide with Plugs” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 9 – 7-Channel CMT Port Cutting Guide with Plugs<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Step 9) Use Cutting Bolts to Cut Holes<\/h2>\n
Next, cut three holes, as described below into Channel 1 using the cutting bolts screwed into the Port Cutting Guide. Do not rush when screwing the cutting bolts into the Port Cutting Guide. Ensure the bolts are properly lined up with the holes in the Port Cutting Guide so that cross threading does not occur. <\/p>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
Do not rush when screwing the cutting bolts into the Port Cutting Guide. Ensure the bolts are properly lined up with the holes in the Port Cutting Guide so that cross threading does not occur. <\/span><\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Start by threading a cutting bolt into one of the holes located on the same side as the window. Use the hex wrench to tighten the Cutting Bolt. Tighten the bolt a few revolutions, then loosen it one revolution. Continue doing this until the Cutting Bolt “bottoms out” (Figure 10). Remove the Cutting Bolt. There should be a plastic disc inside of the cutting bolt. If there isn’t, re-insert the cutting bolt and repeat the cutting process (make sure that the knurled Locking Bolts are tight). Push out the piece of plastic from the inside of the Cutting Bolt by inserting an Allen wrench through the small hole drilled in the head of the Cutting Bolt (Figure 11 ). Repeat this process to cut all three holes. The two upper holes will provide the port plug access and the lowest hole is the vent hole (Figure 12). <\/span><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
For easy effective cutting, advance the cutter bolt in alternating increments of ~1.5 turns clockwise, and then 0.5 turn counter-clockwise, repeatedly.<\/span><\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig7-cutting-port-holes-in-cmt-tubing.webp” alt=”figure 10 cmt port cutting guide – cutting out sampling port hole” title_text=”Figure 10 – CMT Port Cutting Guide – Cutting Out Sampling Port Hole” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 10 – CMT Port Cutting Guide – Cutting Out Sampling Port Hole<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig8-removing-cmt-port-cuttings.webp” alt=”figure 11 cmt removing ldpe cutting plug” title_text=”Figure 11 – CMT Removing LDPE Cutting Plug” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 11 – CMT Removing LDPE Cutting Plug<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig9-marked-cmt-tubing.webp” alt=”figure 12 cmt tubing port cutting setup” title_text=”Figure 12 – CMT Tubing Port Cutting Setup” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 12 – CMT Tubing Port Cutting Setup<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
If installing numerous systems, spare cutting bolts can be ordered, as they may become dull after repeated use. It is recommended to order an extra bolt per 10 ports constructed. <\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Step 10) Cut Panel Between Upper Two Port Holes<\/h2>\n
Loosen the cutting tool and move it “down” the CMT and out of the way. Next, use the snips as shown in Figure 13 to cut out the panel of plastic between the upper two port holes. Do this carefully and keep the snips parallel to the channel side wall to avoid cutting into the walls separating Channel 1 from Channels 2 and 6. Make the opening as large as possible to facilitate the insertion of the expansion plug as described in the next step. <\/p>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
The two upper holes allow you to use snips to cut away a panel of plastic between the two holes, creating a 3-inch long port in Channel 1. The bottom hole is a vent hole. A vent hole is needed to allow air to escape from the channel beneath the monitoring port when the CMT tubing is inserted into the waterfilled borehole during well installation. <\/span><\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig10-cutting-cmt-tubing.webp” alt=”figure 13 cmt port cutting” title_text=”Figure 13 – CMT Port Cutting” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 13 – CMT Port Cutting<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/403-cut-cmt-panel.webp” alt=”figure 14 cut cmt multilevel system panel” title_text=”Figure 14 Cut CMT Multilevel System Panel” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 14<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/403-cmt-standard-port-assembly.webp” alt=”figure 15
\nstandard port assembly 106278″ title_text=”Figure 15 Standard Port Assembly (#106278)” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 15<\/em>
Standard Port Assembly (#106278)<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Step 11) Insert Expansion Plug<\/h2>\n
Insert an expansion plug through the opening (Figure 16) so that it seals Channel 1 below the monitoring port and above the vent hole. If necessary, use the torque driver to gently push the plug into place (Figure 17). Use the snips to trim the port opening if you have difficulty inserting the plug. Tighten the plug to a torque of 12.5 inch-pounds using the supplied torque driver. <\/p>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
The vent hole does not allow cross connection with other monitoring zones because the bottom of the channel is sealed with a water-tight plug.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n
<\/p>\n<\/div>\n<\/div>\n
[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig11-inserting-cmt-pie-plug-into-sampling-port.webp” alt=”figure 16 insert cmt pie plug into sampling port” title_text=”Figure 16 – Insert CMT Pie Plug into Sampling Port” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 16 – Insert CMT Pie Plug into Sampling Port<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig12-403-cmt-torquing-pie-plug-seal.webp” alt=”figure 17 insert solinst cmt multilevel system pie plug into sampling port” title_text=”Figure 17 – Insert Solinst CMT Multilevel System Pie Plug into Sampling Port” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 17 – Insert Solinst CMT Multilevel System Pie Plug into Sampling Port<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
When installing the expansion plug, temperature of the CMT should be between -15\u00baC and 35\u00baC. If air temperature is above 35\u00baC, use cold water to cool down the tubing at the port before installing the expansion plug. <\/span><\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n <\/p>\n<\/div>\n<\/div>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Step 12) Install the Well Screen<\/h2>\n
The last step in making the Channel 1 port consists of wrapping the stainless steel mesh around the port, forming a well screen over the opening. Centre the mesh over the port opening and wrap it tightly around the CMT tubing (Figure 18). Use the low profile Oetiker clamps and pliers to firmly secure the mesh to the tubing. See the section below for more details about installing Oetiker clamps. Use two clamps for each monitoring port (Figure 20). Construction of Port 1 is now finished. You are now ready to make Port number 2. <\/p>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\n\n
\n
\n
\n
\n
\n
\n
\n
\n
Wetting the Oetiker Clamp reduces friction, making installation easier.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Installing Oetiker Clamps<\/h2>\n
Wrap the Oetiker clamp around the part (e.g. screen, centraliser, guide point) you are clamping. Allow the first (closest) retaining hook to pass through the long slot opening. Squeeze the clamp by hand until the retaining hook catches the end of this opening. Figure 19 shows this step. Fit the ‘jaw tips’ of the Oetiker pliers into each of the clamp’s ‘tunnels’. Squeezing\/closing the Oetiker pliers simultaneously draws the two tunnels together. With the two tunnels drawn together, push down on the tail of the clamp, so that the furthest retaining hook passes through the last slot. Now release the pliers so that the retaining hook catches the clamp and holds. <\/p>\n
[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig13-cmt-screen-wrapped-around-port.webp” alt=”figure 18 wrapping stainless steel mesh around cmt sampling port” title_text=”Figure 18 – Wrapping Stainless Steel Mesh around CMT Sampling Port” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 18 – Wrapping Stainless Steel Mesh around CMT Sampling Port<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig14-cmt-screened-port-oetiker-clamp.webp” alt=”figure 19 affixing cmt oetiker clamp over sampling screen” title_text=”Figure 19 – Affixing CMT Oetiker Clamp Over Sampling Screen” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 19 – Affixing CMT Oetiker Clamp Over Sampling Screen<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig15-cmt-screened-port-clamping.webp” alt=”figure 20 tightening oetiker clamp over cmt stainless steel mesh for sampling port” title_text=”Figure 20 – Tightening Oetiker Clamp over CMT Stainless Steel Mesh for Sampling Port” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 20 – Tightening Oetiker Clamp over CMT Stainless Steel Mesh for Sampling Port<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Step 13) Line-up Port Cutting Guide<\/h2>\n
Slide the Port Cutting Guide down to Port 2. Position the Port Cutting Guide exactly as you did for Port 1. The depth mark should be visible in the window of the Port Cutting Guide and the longitudinal Channel 1 identifier should be indexed to the number “1” stamped on the guide (Figure 21). Now, rotate the Port Cutting Guide (without moving its position along the CMT tubing) so that the longitudinal line is now indexed to the number “2” stamped on the guide (Figure 22). This positions the Port Cutting Guide so that the cutting bolts will cut holes only into Channel 2. Secure the Port Cutting Guide using the knurled Locking Bolts as before. Cut the two port holes and one vent hole into Channel 2. Next, loosen the cutting tool and slide it down the tubing out of the way. <\/p>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nTo avoid installing ports in the wrong channels start by positioning the Port Cutting Guide so that the depth mark is visible in the window, then rotate the guide so that the appropriate number (corresponding to the port number) is indexed against the line you drew earlier along the longitudinal Channel 1 identifier. This step is very important <\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig16-cmt-port-guide-cutter.webp” alt=”figure 20 tightening oetiker clamp over cmt stainless steel mesh for sampling port” title_text=”Figure 21 – Aligning CMT Port Cutting Guide to correct Sampling Depth” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 21 – Aligning CMT Port Cutting Guide to correct Sampling Depth<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/fig17-cmt-port-guide-cutter.webp” alt=”figure 22 aligning cmt port cutting guide to the
\ncorrect cmt tubing channel using the numbers allocated at the top” title_text=”Figure 22 – Aligning CMT Port Cutting Guide to the correct CMT Tubing Channel Using the Numbers allocated at the top” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 22 – Aligning CMT Port Cutting Guide to the<\/em>
correct CMT Tubing Channel Using the Numbers allocated at the top<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nAt some sites, you may decide that it is not necessary to monitor every channel. In that case, only cut ports in the desired channels. <\/p>\n
When constructing the bottom assembly, only insert the expandable plugs into the monitored channels, leaving the other channels open so that they can fill with water as the CMT tubing is inserted into the borehole (e.g. If only three channels are monitored, only those channels should have plugs inserted at the base.) This reduces buoyancy during well installation.<\/p>\n<\/div>\n<\/div>\n
[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Step 14) Create Port 2 Opening<\/h2>\n
Snip away the panel of plastic between the upper two holes, creating an opening for Port 2.<\/p>\n
<\/h2>\nStep 15) Finish Constructing Port 2<\/h2>\n
Next, insert an expansion plug through the opening, positioning it below the monitoring port, and tighten it to 10 inch-pounds as before. Finally, wrap a piece of stainless steel mesh around the opening and secure it with two stainless steel clamps. You have now finished constructing Port 2. <\/p>\n
<\/p>\n
Step 16) Construct Ports 3 to 6<\/h2>\n
Continue the steps described above for Ports 3 through 6.<\/p>\n
[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” custom_padding=”0px|||||” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_button button_url=”https:\/\/www.solinst.com\/products\/multilevel-systems-and-remediation\/403-cmt-multilevel-system\/get-quote.php” button_text=”Get Quote” admin_label=”403 get quote” _builder_version=”4.27.4″ _module_preset=”c9e00792-1360-4998-8cf9-5f6772c944ba” hover_enabled=”0″ global_module=”3396″ global_colors_info=”{}” sticky_enabled=”0″][\/et_pb_button][dsm_menu title=”Related Products” menu_id=”37″ submenu_collapse=”on” menu_link_text_color=”#000000″ active_link_color=”#000000″ menu_link_text_active_color=”#000000″ menu_link_text_visited_color=”#000000″ list_style_type=”none” disabled_on=”off|off|on” admin_label=”403 Related Products Mobile” _builder_version=”4.27.2″ _module_preset=”default” header_font=”|600|||||||” header_text_align=”left” header_text_color=”#000000″ header_font_size=”20px” menu_font_size=”16px” sub_menu_text_color=”#727272″ background_color=”#fcfcfc” custom_padding=”10px|10px|10px|10px|false|false” sticky_limit_bottom=”body” sticky_position_tablet=”none” sticky_position_phone=”none” sticky_position_last_edited=”on|tablet” border_width_all=”1px” border_color_all=”#e0e0e0″ box_shadow_style=”preset4″ box_shadow_horizontal=”1px” box_shadow_vertical=”1px” box_shadow_color=”rgba(255,133,0,0.6)” global_colors_info=”{}” active_link_color__hover_enabled=”on|hover” active_link_color__hover=”#d1d1d1″][\/dsm_menu][\/et_pb_column_inner][\/et_pb_row_inner][\/et_pb_column][\/et_pb_section][et_pb_section fb_built=”1″ admin_label=”Adobe Analytics Code” _builder_version=”4.27.0″ _module_preset=”default” custom_padding=”||4px|||” global_colors_info=”{}”][et_pb_row _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_column type=”4_4″ _builder_version=”4.27.0″ _module_preset=”default” global_colors_info=”{}”][et_pb_code admin_label=”AA Code for this page” _builder_version=”4.27.4″ _module_preset=”default” global_colors_info=”{}”]