\n
1\/2″OD x 3\/8″ID or 5\/8″OD x 1\/2″ID tubing can be used. The 1\/2″OD tubing is clamped directly onto the Port Stem with an Oetiker #14 clamp, while the 5\/8″OD tubing fits over a 3″ length of 1\/2″OD tubing before being clamped to the Port Stem with an Oetiker #17 clamp. <\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-installation-tubing-being-pulled-to-mark-fig6-2.webp” alt=”waterloo multilevel system installation figure 6 2 tubing being pulled to reference mark” title_text=”Waterloo Multilevel System Installation Figure 6 2 Tubing Being Pulled to Reference Mark” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-2 Tubing Being Pulled to Reference Mark<\/em><\/p>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nRemember to label each tubing\/cable end.<\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/401-waterloo-system-sampling-port-fig6-3.webp” alt=”waterloo multilevel system installation figure 63 5 8 inch od by one half inch id tubing attached over 3 inch of one half inch od by three eights inch id tubing to port stem using oetiker number 17 clamp” title_text=”Waterloo Multilevel System Installation Figure 63 5 8 Inch Od By One Half Inch Id Tubing Attached Over 3 Inch Of One Half Inch Od By Three Eights Inch Id Tubing To Port Stem Using Oetiker Number 17 Clamp” align=”center” _builder_version=”4.27.2″ _module_preset=”default” width=”20%” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-3 5\/8″OD x 1\/2″ID tubing attached over 3″ of 1\/2″OD x 3\/8″ID tubing to Port Stem Using Oetiker #17 Clamp<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
At the next Port, roll off the tubing to the end of the previous cut tubing length, and cut at this new reference mark. Use this reference for the remaining Ports, so as more Ports are added the tubing and cable ends will meet at the same point. Remember to label each length of tubing as you progress. <\/p>\n
Be sure there is a clean cut to the tubing end at the Port. Place one single ear Oetiker #14 clamp over the tubing and push the tubing end onto the stainless steel Port Stem. Using the Oetiker pliers, squeeze the clamp \u2018shoulders\u2019 together to securely attach the tubing to the stem. <\/p>\n
[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-attaching-tubing-to-port-fig6-4.webp” alt=”waterloo multilevel system installation figure 6 4 one half inch od by three eights inch id tubing attached to port stem using oetiker number 14 clamp” title_text=”Waterloo Multilevel System Installation Figure 6 4 One Half Inch Od By Three Eights Inch Id Tubing Attached To Port Stem Using Oetiker Number 14 Clamp” align=”center” _builder_version=”4.27.2″ _module_preset=”default” width=”60%” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-4 1\/2″OD x 3\/8″ID tubing attached to Port Stem Using Oetiker #14 Clamp<\/em><\/p>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nIf using 5\/8″OD tubing, a 3″ length of 1\/2″OD tubing has to be first pushed onto the Port Stem. Then the 5\/8″OD tubing is pushed over the 1\/2″OD tubing and clamped to the Port Stem with an Oetiker #17 clamp (see Figure 6-3).<\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner admin_label=”6-2″ module_id=”6-2″ _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
6.2 Attaching Vibrating Wire Transducers (VWT)<\/strong><\/h2>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Tools and accessories required: 11\/16″ (18 mm) and 5\/8″ (16 mm) wrenches.<\/span><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-installation-tools-fig6-5.webp” alt=”waterloo multilevel system installation figure 6 5 tools and accessories required” title_text=”Waterloo Multilevel System Installation Figure 6 5 Tools And Accessories Required” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-5 Tools and Accessories Required<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Each one of the VWT’s cables has been cut to the length requested in the original order. This length also includes an additional 10% contingency. The total cable length is labelled on the cable’s end. <\/p>\n
Match the serial number on the VWT body with the labelled cable end, and its corresponding “Vibrating Wire Transducer Calibration Report” provided in the shipment (see Appendix II).<\/p>\n
[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nMatch the serial number on the body of the VWT with the label at the end of the cable.<\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/pre-soaking-vibrating-wire-pressure-transducers-fig6-6.webp” alt=”waterloo multilevel system installation figure 6 6 presoaking the vibrating wire transducers” title_text=”Waterloo Multilevel System Installation Figure 6 6 Presoaking The Vibrating Wire Transducers” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-6 Presoaking the Vibrating Wire Transducers<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Soak all of the VWTs for about 30 minutes, in either the borehole, or in a bucket of water at the same temperature as the borehole water. Once the VWT has stabilised, lift the VWT just out of the water and record the measured transducer temperature and vibration reading. Record this value on the Installation Log as the VWT’s ‘zero value’. <\/p>\n
Compare this ‘zero value’ to the ‘Factory Zero Reading’ on the Calibration Report. These values should not differ by more than 0.1% of full scale. Remember that pressure varies with elevation (your site vs. factory calibration location), temperature, and barometric pressure. <\/p>\n
The ‘zero value’ is used to subtract from all future pressure\/head readings to calculate final depth to water measurements. See Appendix III for a sample depth to water calculation. <\/p>\n
Uncoil the VWT’s cable out to its full length. Push the 3\/8″ SS compression fitting with attached VWT onto the Port Stem. Using the 11\/16″ and 5\/8″ wrenches, tighten the two compression fitting nuts onto the Port Stem by 1 and 1\/4 turns. <\/p>\n
[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-vibrating-wire-pressure-transducer-fig6-7.webp” alt=”waterloo multilevel system installation figure 6 7 vibrating wire transducer” title_text=”Waterloo Multilevel System Installation Figure 6 7 Vibrating Wire Transducer” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nRecord the VWT ‘zero value’ on the Installation Log. It is needed to benchmark against all future readings. <\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-tighening-pressure-transducer-to-sampling-port-fig6-8.webp” alt=”waterloo multilevel system installation figure 6 8 tightening vibrating wire pressure transducer to sampling port” title_text=”Waterloo Multilevel System Installation Figure 6 8 Tightening Vibrating Wire Pressure Transducer To Sampling Port” align=”center” _builder_version=”4.27.2″ _module_preset=”default” width=”45%” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-8 Tightening Vibrating Wire Pressure Transducer To Sampling Port<\/em><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-port-with-vibrating-wire-pressure-transducer-fig6-9.webp” alt=”waterloo multilevel system installation figure 6 9 vibrating wire pressure transducer connected to sampling port” title_text=”Waterloo Multilevel System Installation Figure 6 9 Vibrating Wire Pressure Transducer Connected To Sampling Port” align=”center” _builder_version=”4.27.2″ _module_preset=”default” width=”34%” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6 9 Vibrating Wire Pressure Transducer Connected To Sampling Port<\/em><\/p>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner admin_label=”6-3″ module_id=”6-3″ _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
6.3 Attaching a Pump (Bladder or Double Valve)<\/strong><\/h2>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Tools and accessories required: tubing cutter, Oetiker pliers, Oetiker clamps, sandpaper, 4″ (10 cm) of 1\/2″OD x 3\/8″ID tubing, black electrical tape, rod\/broom handle.<\/span><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-tools-accessories-fig6-10.webp” alt=”waterloo multilevel system installation figure 6 10 tools and accessories required” title_text=”Waterloo Multilevel System Installation Figure 6 10 Tools and Accessories Required” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-10 Tools and Accessories Required<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
There are two stems on each pump. The shorter stem is the sample stem, which the sample line (white\/natural) will be connected to. The longer stem is the drive gas stem, which the drive line will be connected to. Depending on whether you use LDPE or Teflon-lined, the drive line may be red coloured or white\/natural, respectively. <\/span><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-5-8-double-valve-pump-fig6-11.webp” alt=”waterloo multilevel system installation figure 6 11 five eights inch by six inch double valve pump” title_text=”Waterloo Multilevel System Installation Figure 6 11 Five Eights Inch By Six Inch Double Valve Pump” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-11 5\/8″x6″ Double Valve Pump<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Beginning with the deepest Port (Port 1), stand at the borehole holding the spool of tubing. A broom handle or equivalent pole works well to hold the spool. <\/p>\n
Identify\/label the end of this tubing by wrapping a 1″ (25 mm) piece of black electrical tape around the tubing to form a ‘black band’. Let each band represent the Port number. Here, one band of the tape on the tubing end will represent that this tubing will be connected to Port 1. If using Teflon tubing, use a different colour tape to represent the drive line tubing. <\/p>\n
A second person will ‘walk’ the end of the labelled tubing to the measured reference mark. Once the tubing end is pulled to this reference mark. Cut the tubing at the spool. <\/p>\n
At the next Port, roll off the tubing to the end of the previous cut tubing length, and cut at this reference mark. Use this reference for the remaining Ports, so as more Ports are added, the tubing and cable ends will meet at the same point. Remember to label each length of tubing as you progress. <\/p>\n
[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.4″ _module_preset=”e910b435-fe18-45d2-b351-bda808b1a267″ hover_enabled=”0″ border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}” sticky_enabled=”0″]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nUse the black tape to wrap the number of bands corresponding to the Port number around the tubing end (i.e. 1 band of black tape represents Port 1).<\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Make a clean fresh cut to both tubing ends at the borehole. Place one small double ear Oetiker clamp over each pump stem. Wrap a small piece of sandpaper around the tubing for ‘traction’ and push the sample tubing over the shorter pump stem. Use the sandpaper to help push the drive tubing over the longer pump stem. If you are using Teflon-lined tubing, be sure to check that the Teflon lining has not become separated from the tubing while pushing it onto the pump stem. If you see a ‘bubble’ through the tubing, pull it off the stem, make a fresh cut, and restart this step. <\/span><\/p>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” custom_padding=”30px|30px|30px|30px|false|false” border_width_all=”1px” border_color_all=”rgba(0,0,0,0.23)” global_colors_info=”{}”]<\/p>\n
\n
\n
Note: <\/strong><\/h3>\nIf you are using Teflon-lined tubing, be careful not to allow the Teflon lining to become separated and cause a visible ‘bubble’ at the Port Stem.<\/span><\/p>\n<\/div>\n<\/div>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-using-sand-paper-to-push-tubing-onto-pump-fig6-12.webp” alt=”waterloo multilevel system installation figure 6 12 using sand paper to push tubing onto pump stem” title_text=”Waterloo Multilevel System Installation Figure 6 12 Using Sand Paper To Push Tubing Onto Pump Stem” align=”center” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-12 Using Sand Paper to Push Tubing onto Pump Stem<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Using the Oetiker pliers, incrementally crimp both ears on each clamp. Alternate from one ear to the other, slowly pinching the ears closed. Repeat this cycle 2 or 3 times to achieve a proper crimp. Once the clamp is closed properly you should not be able to see light through the ears of the clamp. <\/p>\n
Cut a piece of 1\/2″OD x 3\/8″ID tubing about 4″ (100 mm) long. Push this onto the Port Stem by about 2″ (50 mm). Using the Oetiker pliers, crimp a #14 Oetiker clamp over the tubing, attaching it to the Port Stem. <\/p>\n
[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-tubing-attached-to-port-stem-fig6-13.webp” alt=”waterloo multilevel system installation figure 6 13 tubing attached to port stem” title_text=”Waterloo Multilevel System Installation Figure 6 13 Tubing Attached To Port Stem” align=”center” _builder_version=”4.27.2″ _module_preset=”default” width=”30%” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-13 Tubing Attached to Port Stem<\/em><\/p>\n[\/et_pb_text][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Place another #14 Oetiker clamp over the open 1\/2″OD x 3\/8″ID tubing end. Push the pump intake into the tubing end. You will notice that the pump intake is recessed to receive the Oetiker clamp. Crimp the clamp to the pump. <\/span><\/p>\n[\/et_pb_text][et_pb_image src=”https:\/\/www.solinst.com\/wp-content\/uploads\/2024\/11\/waterloo-system-pump-connected-to-port-stem-fig6-14.webp” alt=”waterloo multilevel system installation figure 6 14 pump connected to port stem” title_text=”Waterloo Multilevel System Installation Figure 6 14 Pump Connected To Port Stem” align=”center” _builder_version=”4.27.2″ _module_preset=”default” width=”30%” global_colors_info=”{}”][\/et_pb_image][et_pb_text _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]<\/p>\n
Figure 6-14 Pump Connected to Port Stem<\/em><\/p>\n[\/et_pb_text][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner _builder_version=”4.27.4″ _module_preset=”3676f7e6-7b83-4698-94ce-2cc9fa9ae43d” hover_enabled=”0″ global_colors_info=”{}” sticky_enabled=”0″][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_button button_url=”https:\/\/www.solinst.com\/products\/multilevel-systems-and-remediation\/401-waterloo-multilevel-system\/get-quote.php” button_text=”Get Quote” admin_label=”401 get quote button” _builder_version=”4.27.4″ _module_preset=”c9e00792-1360-4998-8cf9-5f6772c944ba” hover_enabled=”0″ global_module=”3368″ saved_tabs=”all” global_colors_info=”{}” sticky_enabled=”0″][\/et_pb_button][\/et_pb_column_inner][\/et_pb_row_inner][et_pb_row_inner disabled_on=”off|off|on” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_column_inner saved_specialty_column_type=”3_4″ _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][dsm_menu title=”Related Products” menu_id=”46″ submenu_collapse=”on” menu_link_text_color=”#000000″ active_link_color=”#000000″ menu_link_text_active_color=”#000000″ menu_link_text_visited_color=”#000000″ list_style_type=”none” admin_label=”401 Related Products” _builder_version=”4.27.4″ _module_preset=”default” header_font=”|600|||||||” header_text_align=”left” header_text_color=”#000000″ header_font_size=”20px” menu_font_size=”16px” sub_menu_text_color=”#727272″ background_color=”#fcfcfc” custom_padding=”10px|10px|10px|10px|false|false” sticky_limit_bottom=”body” sticky_position_tablet=”none” sticky_position_phone=”none” sticky_position_last_edited=”on|tablet” border_width_all=”1px” border_color_all=”#e0e0e0″ global_colors_info=”{}” active_link_color__hover_enabled=”on|hover” active_link_color__hover=”#d1d1d1″][\/dsm_menu][\/et_pb_column_inner][\/et_pb_row_inner][\/et_pb_column][\/et_pb_section][et_pb_section fb_built=”1″ admin_label=”Adobe Analytics Code” _builder_version=”4.27.0″ _module_preset=”default” custom_padding=”||4px|||” global_colors_info=”{}”][et_pb_row _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”][et_pb_column type=”4_4″ _builder_version=”4.27.0″ _module_preset=”default” global_colors_info=”{}”][et_pb_code admin_label=”AA Code for this page” _builder_version=”4.27.2″ _module_preset=”default” global_colors_info=”{}”]